 |
This package includes two high-capacity, compact, and lightweight BiXPower BP100 rechargeable batteries, each with a 100Wh capacity (totaling 200Wh). It features a specialized DC cable designed exclusively for the ResMed AirSense 11 CPAP machine.
Package Contents:
- Two BP100 batteries
- One specialized DC cable for ResMed AirSense 11
- One Y25 split cable
- One AC charger
- One car charger
The two BiXPower BP100 batteries can power a ResMed AirSense 11 CPAP machine for approximately 2–4 nights of continuous use, based on average CPAP pressure, typical breathing rate, an optimal mask seal, and with the humidifier, heated tubing, and exhalation pressure relief disabled. This is a rough estimate, as power consumption varies significantly depending on settings and environmental conditions. For instance, at a low pressure setting, the machine may draw 10–12W, allowing a single battery to last up to 16 hours. At a moderate setting, it may draw 20–25W, reducing battery life to about 8 hours. To maximize battery runtime, disable the CPAP’s humidifier and heater and set the pressure as low as possible (with your doctor’s approval).
Each BP100 battery can be used independently with the ResMed CPAP cable. Simply connect the ResMed DC converter to Output Port I (set to 24V) of a BP100 battery as follows:
You can also use both BP100 batteries simultaneously for extended power. Set the output voltage of Port I on both Battery 1 and Battery 2 to 24V. Connect the male ends of the Y25 split cable to Port I of each battery, then attach the S10 special cable to the female end of the Y25 split cable, as shown in the accompanying photos:
Notes: When link two batteries together, one battery may run out of power earlier than the other — this is completely normal. Each battery can independently power your CPAP machine; connecting two batteries together simply extends the total operating time without interruption.
BP100 battery compact size allows it to easily fit into a laptop/notebook carry bag.
Battery Specifications:
|
Model:
|
BP100
|
|
Capacity:
|
100 Watt-Hour
|
|
Battery Cell:
|
Lithium-ion
|
|
Input Charging Port:
|
Input Voltage Range: DC 12 ~ 24V. Connector Size: 5.5 x 2.5mm
|
|
Outputs:
|
Port I:
Output Voltage: 16V, 19V or 24V selectable
Output Connector Size: 5.5 x 2.5mm
Maximum Output Current: 4A @16V, 3.5A@19V, 2.5A@24V
Port II: Nominal Output Voltage 11.1V
Output Voltage Range 9V ~ 12.6V
Output Connector Size: 3.5 x 1.35mm;
>Maximum Output Current: 5A
Port III: 5V USB Port; Maximum Output Current: 2.A
Total maximum output with all 3 outputs: 65W
|
|
Charging time /Temperature
|
4-6 hours / 0～45 ℃
|
|
Size
|
180 x 110 x 22.5mm ( or 7.2" x 4.2" x 0.9")
|
|
Weight:
|
621g ( or 1.4 lb)
|
|
Power Indicator:
|
4 level LED indicator
|
|
Built-in Protection Circuit:
|
-Over-charge ; Over-discharge; Over current ;Over temperature
- Short circuit protection
|
|
Operating Temperature:
|
-20～ 60 ℃
|
|
Storage Temperature:
|
- 20～40 ℃
|
This battery is made with high quality Li-ion battery cells and is compatible with many devices that need 15V, 16V, 16.5V, 18V, 18.5V, 19V, 19.5V, 20V or 24V DC power. The 24V voltage with special cable specially designed for the ResMed CPAP Machine can output voltage to 24V DC power with special configuration. The 5V USB port can power many small devices such as smart phones, tablets.
This Universal External Lithium Rechargeable Battery Pack can provide power for laptop computers, digital cameras, digital photo frames, PDAs, cell phones, DVD players.
This battery features 3 output ports.
Output Port I
Output Port I features 3 different regulated voltages through a hardware volt selection switch: 16V, 19V, 24V. This port can be used to power laptop notebook computers. Please set the port I output voltage close to your laptop power adapter output voltage or laptop's input voltage. Please set voltage at 24V for ResMed AirSense 11 machines Special cable for ResMed:
You may also use BP100 battery for other devices. It has two other ports: Output Port II & Port III
Port II's output voltage range is 9V to 12.6V. Nominal voltage is 11.1V. When the battery is fully charged, its voltage is 12.6V. Output voltage will then decrease gradually. Most of the time, the output voltage will be around 10V ~ 11V ( nominal voltage is 11.1V). When the voltage drops to 9V, the port will shut off and stop providing power. This port can be used to power portable DVD players and digital photo frames.
Output III is a 5V USB port. Its maximum output current is 2.1A, which can be used to power or charge iPad, tablet computers and any other device that can be charged from a USB port (USB power cable not included).
Charge the battery: This battery can be charged from any 100V ~ 240V, 50Hz/60Hz AC power source with the battery AC charger.
You may charge each battery separately:
You may also charge two batteries together with Y25 split cable like this:
You may use battery while it is under charging.
This battery has built-in charging controller to control the charging process. It can accept a very wide range of voltage for charging. You can use a regular power adapter with 12V to 24V DC power to charge the battery. The battery charge port is a 5.5 x 2.5mm female jack, therefore a 5.5 x 2.5mm male connector is required.
Car Charger:
You may also charge batteries from a 12V car cigarette socket with cr charger:
You may also charge two batteries together with split dongle:
Package Contents:
The battery pack comes with Two BP100 batteries + One ResMed AirSense 11 Power Cable + One Y25 Split cable + AC Charger + Car Charger
Battery Running Time: The runtime of the BiXPower BP100 batteries varies significantly based on the CPAP machine’s settings and operating environment, with power consumption ranging from 10W to 90W. This results in a battery life of approximately 2 to 10 hours. To maximize runtime, disable the CPAP machine’s humidifier and heater and adjust the pressure to the lowest effective setting (with your doctor’s approval).
|
|
|